PolyIQPolyIQPolyIQ · a Brocone Company

Quote the part. Design the mold. Set up the press.

PolyIQPolyIQPolyIQ is software for injection molders, tool shops and resin distributors, built around your own part files, presses and grades. Each value is labeled as calculated, a guideline, supplier data or measured.

Bring a part file, a press list or a recent quote. We go through it in the product with you.

Engine output for the hot runner cap showcase: 4 cavities, PP, valve-gated 4-drop manifold. Checked for interference, release and opening/ejection kinematics. Concept tooling, not a released design; hot-runner parts are generic provisional envelopes.

Source labels on every value

A clamp estimate from a formula is not the same as a clamp force measured on your press. PolyIQPolyIQPolyIQ labels each value so the difference is visible. Anything not marked V is provisional until someone checks it.

The same labels run through the mold concept, the setup sheet, the BOM and the quote.

FFormula
Calculated from stated inputs, such as clamp tonnage from projected area. Check the inputs.
GGuideline
A rule of thumb, such as a draft or rib ratio. Good for judging feasibility, not for cutting steel.
SSupplier data needed
Unknown until the supplier or customer documents it: resin data, hot-runner sizes, a price.
STDYour shop standard
Taken from your company's tooling standards, in place of the generic guideline.
VValidated
Measured, tested or documented on this project. Nothing becomes V by being copied into CAD.

PolyIQPolyIQPolyIQ Process

Builds a starting process from the press, the mold and the grade.

  • Setup sheets held inside the press's real clamp, shot and injection range
  • Five molding studies, from viscosity curve to process window, saved per tool
  • Defect troubleshooting with the corrections to try, in order

For process engineers, technicians and quality.

More on PolyIQPolyIQPolyIQ Process →

Setup sheet

Hot runner cap · 4 cavities

Tool from PolyIQPolyIQPolyIQ Tooling

Sample 55 t all-electric · sample press

  • Barrel utilization48 %passes
  • Melt residence time1.1 minpasses
  • Clamp force30.3 % of presspasses
  • Gate shear rateneeds gate sizenot calculated
  • Screw surface speed0.3 m/spasses
Melt temperature
225 °C
Mold temperature
40 °C
Fill time
1 s
V/P transfer at
96 % of fill
Pack / hold pressure
2,074 psi plastic
Hold time
4.3 s
Cooling time
14 s
Estimated cycle time
23.3 s

Every value is an estimate from PP family data, not a supplier datasheet. Add the grade's datasheet and they become datasheet values.

Calculated by the PolyIQPolyIQPolyIQ Process engine for the hot runner cap shown on the Tooling page (4 cavities, PP, 23.7 g shot, valve-gated) on a sample 55 t press: the press checks pass (gate shear waits for a gate size), cycle about 23.3 s. On a 110 t press with a larger barrel the same job fails the barrel-use check.

PolyIQPolyIQPolyIQ CRM

Runs the commercial side: accounts, quotes, orders, lots and shipments.

  • Quotes with quantity breaks, PDF output and email from the record
  • Parts, tooling projects and mold maintenance for molders and tool shops
  • Lots, purchase orders and shipments on a stock ledger

For sales, customer service and program managers.

More on PolyIQPolyIQPolyIQ CRM →

Quote · Lakeview Outdoor (sample)

Hot runner cap · 4 cavities

Cycle from PolyIQPolyIQPolyIQ Process
  1. RFQ
  2. Quote
  3. Order

Price per part

$0.1415

Machine time
9.08¢
Resin
1.13¢
Packaging
0.40¢
Margin
3.54¢

At 500,000 parts a year

Revenue
$70,759
Press hours
826 h
Resin
6,664 lb PP
Cycle
23.3 s · 4 cavities

Sample inputs: PP at $0.85/lb, press $55/h, 2% scrap, 25% target margin. Tooling is quoted as its own line, not hidden in the piece price.

Priced by the PolyIQPolyIQPolyIQ CRM piece-price engine for the same hot runner cap as the Tooling and Process pages: the part and cavities from the Tooling build, the 23.3 s cycle from the Process setup sheet (an estimate). The press hours feed PolyIQPolyIQPolyIQCommand's capacity view.

PolyIQPolyIQPolyIQ Command

Tells the owner whether the quote pipeline covers the open press hours.

  • Capacity gap by press against your utilization target
  • Open quotes weighted by press hours and win probability
  • The rows behind every number, one click away

For owners, general managers and plant managers.

More on PolyIQPolyIQPolyIQ Command →

Sample shop · 3 presses · next 90 days

Can the pipeline fill the presses?

Short

Open press hours

562

to reach 80% load

Weighted pipeline

429

hours × win odds

Coverage

0.76x

target 1.25x

Open quoteHoursWinWeighted
Sensor housing (sample)31060%186
Hot runner cap (sample customer)20450%102
Precision gear (sample)24040%96
Door panel carrier (sample)18025%45

Decision due

Pipeline does not cover the capacity gap

Add 133 weighted press hours or lower the utilization target.

Sample presses, quotes and rates, run through the same calculation Command uses on your records.

The mold at the top of this page is PolyIQPolyIQPolyIQ Tooling: a desktop app that turns a customer STEP file into a checked mold concept. More on PolyIQPolyIQPolyIQ Tooling →

One part, from concept to press

The products are sold separately and share their records. A mold concept from Tooling becomes the part and the tool in CRM and Process. The shrink and cycle you measure at the press go back to the Tooling job and replace its estimates.

Injection molders
Quote the part, run the program, set up the press and see where press hours go.CRM · Process · Command
Tool shops
Check incoming parts, build mold concepts and track tooling projects to ship date.Tooling · CRM
Resin distributors
Manage programs and samples, price by contract and quantity break, and track lots and freight.CRM · Command
  1. PolyIQTooling
    1. Check and design

    Part file to a checked mold concept, BOM and tool estimate.

    Part files stay on your computer

    part and estimate
  2. PolyIQCRM
    2. Quote

    Tool and piece price, issued to the customer and linked to the job.

    part and mold
  3. PolyIQProcess
    3. Set up and run

    Setup sheet for the mold on your press. Trials saved to the tool.

Measured shrink and cycle return to the Tooling job, replacing estimates for that tool revision
PolyIQCommand

Reads quotes, parts and press hours across all three: capacity, pipeline and what to decide next.

One company account: Accounts · Parts · Molds · Presses · Materials

Where the software runs and who sees what

Web apps
CRM, Process and Command run in the browser. Nothing to install.
Buy what you need
Each company gets the products it uses. Tooling is licensed per seat.
Company isolation
Each company's records are kept separate. Users join by invite and get a role.
Local geometry
PolyIQPolyIQPolyIQ Tooling runs on your computer. Part files and mold geometry stay on that machine.

PolyIQPolyIQPolyIQ Tooling is in pilot. Its installer downloads from your account.

See PolyIQPolyIQPolyIQ on your own parts and presses.

Send a part file, a press list or a recent quote, and we will go through it in the product with you.